Click to enter the product page

High temperature resistant fireproof insulation fiber textiles
Products - Cloth / Strap / Round Rope / Square Rope / Casing
Continuous temperature resistance 260°C-1300°C
Acid and alkali resistant / weather resistant / airtight / non-combustible / aluminized / aluminum foil / silicone / Teflon coating and other surface treatments

Click to enter the product page

RE-Sil red silicone coated glass sleeve
- Continuous temperature resistance 260°C
- Special red silica gel, with thermal stability at high temperatures
- Not easy to stick to molten iron slag, increase the protection of pipelines
- Flexible, easy to install and install
- Full inches range, 1/4" - 5" (inner diameter), 1/8" thick

KM1000 Ultra-high temperature resistant silica fiber sleeve
- Continuous temperature resistance 1000°C
- Melting point 1650 °C can resist molten iron without being melted
- Inner diameter 1/4" - 4.5", thickness 1.6mm

High temperature resistant fiberglass sleeve
- Continuous temperature resistance 540°C
- Resistant to most corrosive chemicals
- Inner Diameter 1/4" - 5", Thickness 1/16" and 1/8"

Click to enter the product page

SIB ultra-low heat transfer insulation blanket Advantages:
1. Energy conservation and carbon reduction
2. When the waste disposal of general thermal insulation materials or environmental pollution damage is bound to become a cost that you must and cannot afford
3. When electricity, gas, fuel oil... When energy prices rise sharply or even cannot be obtained in sufficient quantities, and the energy saving (thermal insulation) of traditional insulation materials cannot provide you with a solution

SIB ultra-low heat transfer blanket features:
- Thermal conductivity 0.021 - 0.128 w./m.k.
- At the same thickness:
Lower surface temperature and more energy savings (significantly reduced energy consumption)
- At the same table temperature:
Half the thickness or thinner for energy savings (smaller heat dissipation surface area)
- Non-absorbent, with overall water repellency (not only the surface), allowing free evaporation of water vapor, suitable for outdoor use, reducing the worry of corrosion of equipment pipelines due to moisture residue
- High compressive resilience, does not change its thermal insulation performance due to installation or extrusion
- With the choice of inner outer covering, its service life can be far better than other materials
- No safety and health environmental issues, non-combustible or flame retardant (Class A –ASTME84) and RoHS compliant

Click to enter the product page

Ceramic fiber blanket
- 1260°C, 1400°C, 1600°C three temperature resistance grades

Ceramic fiber paper
High-purity ceramic paper made by mixing and processing lightweight refractories is recommended for continuous use up to 1260°C

KM600 & KM1000 needle tie blanket
The length of a revolutionary insulation blanket is made of long fibers continuous high-temperature resistant filament needled

Click to enter the product page

High-strength heat insulation hard plate for mold
This series is a high-temperature resistant and high-strength composite plate developed and manufactured for high-temperature mold insulation and heat insulation. Compared with the fiber cement board or calcium silicate board currently used in the market, it will bring you the following characteristics:
- Does not contain asbestos or other harmful substances
- Low thermal conductivity
- High compressive and impact strength at operating temperature
- Very low moisture absorption (no cracking)

Click to enter the product page

High temperature resistant ceramic glue
Air-dried high-temperature ceramic glue to 1350°C

Applications
- Fill the gaps in the refractory materials of the high-temperature furnace body
- Bonding between refractory and refractory or refractory and iron plate

Fabric joints
Maximum operating temperature: 1350°C
Application amount: 1 to 4 kg/m2 (varies depending on application thickness and surface roughness and porosity)
How to apply:
Apply with a scraper or brush (stir well before use)
Storage: Store in a dry and cool place, avoid direct sunlight after opening, unused, be sure to seal immediately
Packing: 3 kg/drum, 4kg/drum or 15kg/drum

Click to enter the product page

High temperature resistant sewing threads

Product Description and Features:
KM600 sewing thread is specially designed to replace asbestos and various forms of synthetic sewing thread for high temperature and special use in removable and reusable heat insulation clothing, fire blinds, expansion joints

KM600 sewing thread surface is mainly coated with Teflon lubricant to improve the convenience of sewing operation (not easy to break), all Teflon coated sewing thread will not burn or continue to oxidize under normal atmospheric pressure and will not be attacked by bacteria, acid and alkali corrosion

Click to enter the product page

FLUOSEAL-D coatings and caulks
Material: Viton
Resistant to almost all corrosive chemicals, organic solubilities, ultraviolet rays and ozone
- Single dose, direct application, no prior preparation required
- Temperature resistance 204°C
- 285% elongation
- Tension strength 1655Psi
- Solid content 75%
- 0% porosity, good sealing performance
- High adhesion, can be used on metal, concrete, glass, ceramic and other rubber and plastic surfaces
- Can permanently store and not deteriorate (other storage time for mixing of two doses is only about 4 hours)

FLUOSEAL-T caulk
Material: 100% soft expansion Teflon PTFE
- Temperature resistance -240°C~260°C, applicable PH value 0-14
- With adhesive backing, easy to install and use
- Cut the required length according to the needs to save materials
- Non-flammable, non-toxic, does not react with sealed fluids
- Can be stored for a long time without deterioration
- Suitable for use in the food industry
- High compressibility, provides a tight sealing effect, can be used on irregular surfaces

Click to enter the product page

CBF High Temperature Resistant Acid and Alkali Flexible Fittings/Hoses
- Temperature resistance: -178 to 316°C
- Corrosion / weather / UV
- Suitable for: anti-sticking, dust-free and clean, biochemical, food, semiconductor, medical and other places
- Flame resistant: L.O.I. 95, FM4910, UL94V-O, CNS 10285 Grade 1
- Soft, easy to bend and elongated compression
- Antistatic surface treatment available upon request
- Airtight pressure resistance and bending resistance far superior to all Teflon coated fiberglass materials on the market

CBF material properties
CBF is 100% Teflon PTFE with special bending resistance,
(The folding resistance is 7.8 times that of general PTFE, 1276 times that of FEP, and 1510 times that of PFA)
- Tear strength much greater than other fluorinated plastic materials (up to about 6 times)
- Acid and alkali corrosion resistance is the same as PTFE, PH 0-14
- The service life far exceeds that of PTFE, FEP, PFA and other materials
- CBF received "Chemical Processing's Vaaler" and DuPont "Plunkett" awards

Click to enter the product page

TJ-Flex anti-vibration connectors
TJ-Flex non-metallic anti-vibration joints are mainly used to absorb the deformation caused by thermal expansion and contraction of high temperature, vibration caused by windmills, and deviation caused by piping

Expansion joints
The joints provided are made of the highest quality materials whether they are single-layer or multi-layer construction, cloth or fluorinated rubber (Viton, Fluorel) to overcome the problems encountered by high temperature or exhaust gas pipelines, displacement, high temperature, corrosion, dust particles, and vibration

Click to enter the product page

TS-6 expansion joint
- The displacement absorption of TS-6 expansion joints, whether axial expansion, lateral displacement, angular deflection, is much greater than that of general standard flexible joints
- TS-6 fittings are made of non-flammable or flame retardant (FM4910 or other flame resistance standards) and can be designed according to the needs for gas pipelines with temperature to 260°C and corrosive ingredients (acid, alkali and organic solvents).
- TS-6 joint structure is strong, durable, light weight - easy to install, and all are made by experienced professionals, the quality is no less than any well-known large factory (ISO9001-2008 certification) So far, hundreds of sets of TS-6 expansion joints have been installed in semiconductor factories, photovoltaic power plants, petrochemical plants, power plants, etc., in terms of function and service life have reached or even exceeded the needs of users

Click to enter the product page

CBF high-strength PTFE film plate
CBF corrosion resistant series is made of 100% PTFE
Designed for some of the most challenging applications in the industry, the soft CBF series has extremely high strength and crack resistance.
The PF series is a multi-layer crossfilm platen that can support itself, which does not require skeleton material at all, avoiding the possibility that skeleton material will be affected by chemicals
CBF Materials received DuPont's Plunkett Award and Chemical Processing's Vaaler Award in 1995.

Click to enter the product page

Thermal cloth bag
This series of products is made of non-asbestos high-temperature resistant cloth as the inner and outer layers, filled with glass fiber needle rolled blanket, rock wool or ceramic fiber blanket, made by sewing, which can replace most of the traditional aluminum skin non-rageous steel sheet coated with glass wool, rock wool or calcium silicate board, perlite insulation mud insulation method
- Short construction time, easy loading and unloading, and can be used many times
- Excellent heat insulation effect
- Waterproof, oilproof, durable, safe

Click to enter the product page

High temperature P-shaped sealing tape
In a high temperature environment with low furnace pressure, flange pressure plate surface deformation is uneven, bolt locking force is small, and often open and close the furnace door, P-shaped sealing strip will provide you with the most appropriate high-temperature sealing pressing function, using high-temperature woven fiber rope, or non-cheng steel core material, wrapped with high-temperature fireproof cloth, made of high-temperature sewing thread, and selected different combinations of P-shaped sealing strips
Available for you
- Temperature resistant to 1100°C
- Maintain elasticity under repeated pressure, solve the problem of general high temperature sealing pressing material losing elasticity and causing heat source leakage
- No dust, fiber shedding problem, can be applied to dust-free environment
- High compression ratio, low locking force can achieve the required sealing effect
- A variety of inches and materials to choose from, cost-effective according to needs

Click to enter the page

KM-EL flexible heating cloth bag and temperature control system
The electric hot wire, temperature control switch, and temperature measuring thermocouple are installed on the high-temperature cloth, and then sew with soft high-temperature cloth and blanket and other materials, and are connected to the controller by the outer outlet

KM-EL features:
- According to the shape of the heated object, the electric heating and insulation are made into one, fixed with hook tape or strap, and directly connected to the controller with a connector, which is easy to install
- Obvious thermal insulation effect, low surface temperature, high electric heating efficiency, low electrical energy loss, customized according to the needs of square feet, the heating surface is close to the heated element, and the temperature distribution is even
- Heating temperature can be designed to 1000°C
- Inner and outer high-temperature cloth and stitching, hook and loop straps can be used in cleanroom environments
- High-temperature cloth, insulation and sewing are non-combustible or flame-resistant
- An electric heating layer with moisture-proof and moisture-proof functions can be provided upon request, and the thickness can be as thin as about 1. 2mm,
There are a variety of electric hot wires, high-temperature cloths, thermal blankets, sewing threads, etc. of different materials, and the most suitable combination can be flexibly selected according to the conditions of use

Click to enter the product page

Injection machine heating tube/ barrel insulation cloth
Characteristic:
- The materials used in this series of products are all non-asbestos high-temperature resistant fibers
- Short construction time, easy loading and unloading, and can be used many times, no need for professionals to work
- Excellent heat insulation effect, achieve the best thermal insulation effect in limited space
- Waterproof, oilproof, durable, safe, no asbestos substances, avoid fiber flying, no environmental safety problems

Introduction to examples
The main purpose of our joint project with the Plastics Center is to reduce the heat loss of injection molding machines in order to achieve energy saving, carbon reduction, and energy cost savings